HVAC Cost Guide for Fort Worth & the DFW Metroplex
Typical installed-cost ranges for AC-only replacements, full systems, furnaces, and ductless mini-splits, so you know what to expect before we ever step in your home.
Reviewed by our licensed HVAC technicians · TACLA#148830E · Updated August 16, 2026
Quick answer
In Fort Worth and the greater DFW Metroplex, Family First Comfort's installed HVAC costs typically range from about $2,500 for a small single-zone mini-split up to $15,000 for a full system replacement — see the exact range for your setup below.
All Four Categories at a Glance
| Category | Typical installed cost |
|---|---|
| AC-Only (Coil & Condenser) | $7,000 – $13,500+ |
| Full System (Furnace / Heat Pump / Heat Kit) | $8,500 – $15,000+ |
| New Furnace | $3,000 – $6,000 |
| Ductless Mini-Split | $2,500 – $10,500 |
How to read these numbers
These are typical installed-cost ranges as of 2026, not a guaranteed quote. Your exact price depends on SEER rating, ductwork, electrical needs, and access to your equipment. Call (817) 935-8540 or request an estimate for an exact number in writing.
What's Included
Equipment
The outdoor unit, indoor coil/air handler, or furnace itself.
Standard labor
Installation labor under normal, straightforward conditions.
Removal and disposal
Proper removal and disposal of your old equipment and refrigerant.
Refrigerant
The refrigerant charge needed to run your new system.
Permit
The required city permit and inspection fee.
Thermostat
A new thermostat, if your existing one isn't reused.
Startup and testing
Final startup, safety check, and airflow test.
Manufacturer registration
Registering your new equipment with the manufacturer for warranty coverage.
AC-Only Coil & Condenser Cost by Size
Replacing just the outdoor condenser and indoor coil, keeping your existing furnace or air handler.
In Fort Worth and the greater DFW Metroplex, replacing just the AC condenser and coil with Family First Comfort typically costs $7,000–$13,500 installed, depending on system size.
| System size | Typical installed cost |
|---|---|
| 1.5 ton | $7,000 – $10,000 and up |
| 2.0 ton | $7,500 – $10,500 and up |
| 2.5 ton | $8,000 – $11,000 and up |
| 3.0 ton | $8,500 – $12,000 and up |
| 3.5 ton | $9,000 – $12,500 and up |
| 4.0 ton | $9,500 – $13,000 and up |
| 5.0 ton | $10,000 – $13,500 and up |
These prices are estimates based on equipment and installation, and may change based on SEER rating, complexity, and duct modifications.
Full System Cost — Furnace / Heat Pump / Heat Kit
A complete system replacement: outdoor unit paired with a new furnace, heat pump, or electric heat kit.
A full HVAC system replacement (furnace, heat pump, or heat kit paired with a new outdoor unit) from Family First Comfort in Fort Worth and the greater DFW Metroplex typically costs $8,500–$15,000 installed, depending on size.
| System size | Typical installed cost |
|---|---|
| 1.5 ton | $8,500 – $12,000 and up |
| 2.0 ton | $9,000 – $12,500 and up |
| 2.5 ton | $9,500 – $13,000 and up |
| 3.0 ton | $10,000 – $13,500 and up |
| 3.5 ton | $10,500 – $14,000 and up |
| 4.0 ton | $11,000 – $14,500 and up |
| 5.0 ton | $11,500 – $15,000 and up |
These prices are estimates based on equipment and installation, and may change based on SEER rating, complexity, and duct modifications.
New Furnace Cost by Size
Furnace-only replacement, sized by output (BTU).
A furnace-only replacement from Family First Comfort in Fort Worth and the greater DFW Metroplex typically costs $3,000–$6,000 installed, depending on BTU output.
| Furnace size | Typical installed cost |
|---|---|
| 40,000 BTU | $3,000 – $4,500 |
| 60,000 BTU | $3,500 – $5,000 |
| 80,000 BTU | $4,000 – $5,500 |
| 100,000 BTU | $4,500 – $6,000 |
Prices change based on furnace efficiency, complexity of install, and compatibility with your home.
Ductless Mini-Split Cost by Size
Single or multi-zone ductless systems, sized by total tonnage.
A ductless mini-split system from Family First Comfort in Fort Worth and the greater DFW Metroplex typically costs $2,500–$10,500 installed, depending on tonnage and number of zones.
| System size | Typical installed cost |
|---|---|
| 0.75 ton | $2,500 – $5,000 |
| 1 ton | $3,000 – $5,500 |
| 1.5 ton | $3,500 – $6,000 |
| 2 ton | $4,000 – $6,500 |
| 2.5 ton | $5,500 – $9,000 |
| 3 ton | $6,000 – $9,500 |
| 4 ton | $7,500 – $10,000 |
| 5 ton | $8,000 – $10,500 |
Mini-split cost can vary based on SEER rating, complexity, required electrical upgrades, and zones/number of heads.
This is a budgeting range, not a quote. Family First Comfort will always confirm an exact price for your home before any work starts.
What Affects Your Final Price
Every range above is a starting point. These are the factors that most often move a job toward the higher end of the range.
Ductwork condition
Modifying, extending, or replacing ductwork adds labor and materials beyond the base install.
Electrical requirements
Older homes often need a panel upgrade or new circuit to support a new outdoor unit or mini-split.
Access and complexity
Attic installs, tight closets, or second-story equipment take longer than a straightforward ground-level pad.
Efficiency and equipment tier
Higher-SEER and variable-speed equipment costs more upfront but can lower long-term utility bills.
Permits and inspections
Permit fees and inspection requirements vary by city within the DFW metroplex.
Removal and disposal
Proper removal and disposal of your old equipment and refrigerant, handled to code, is part of the job and factors into the total cost.
Frequently Asked Questions
How much does it cost to replace just the AC condenser and coil?+
Typically $7,000–$13,500 and up depending on system size, if you're keeping your existing furnace or air handler and only replacing the outdoor condenser and indoor coil. See the size-by-size table above for your tonnage.
How much does a full system replacement cost?+
A full system — new outdoor unit paired with a new furnace, heat pump, or heat kit — typically runs $8,500–$15,000 and up depending on size. This is the right comparison if your indoor equipment is also being replaced.
How much does a new furnace cost by itself?+
A furnace-only replacement typically runs $3,000–$6,000 depending on BTU output, efficiency, and how complex the install is.
How much does a ductless mini-split system cost?+
Mini-splits typically run $2,500–$10,500 depending on tonnage and number of zones. Multi-zone systems cost more per ton than single-zone because each indoor head and its wiring adds labor.
Why do these prices say "and up"?+
The number is a realistic starting point, not a ceiling. Your final price depends on SEER rating, ductwork condition, electrical requirements, and how accessible your equipment is — we'll always give you an exact number after a free on-site look.
Are these prices a guaranteed quote?+
No. These are typical installed-cost ranges to help you budget. Every home is different, so we'll always confirm an exact price in writing before any work starts.
Does Family First Comfort offer free estimates in Fort Worth and the DFW Metroplex?+
Yes. We provide free, no-pressure on-site estimates for AC, furnace, heat pump, and mini-split installations throughout Fort Worth and the greater DFW Metroplex.
What HVAC brands does Family First Comfort install?+
We're a Daikin Comfort Pro Dealer and also install and service Trane, American Standard, Lennox, Carrier, Rheem, Amana, Goodman, Ruud, York, and LG, among other major residential brands.
Does financing affect the total installed cost?+
Financing doesn't change the installed cost of the equipment, but it can lower what you pay upfront by spreading payments over time. See our financing options page for current plans.
What's included in an HVAC installation price?+
Every installed-cost range above includes equipment, standard labor, removal and disposal of your old equipment and refrigerant, the refrigerant charge, the required permit, a thermostat if yours isn't reused, startup and testing, and manufacturer registration for your warranty.
How is Family First Comfort rated in Fort Worth and the DFW Metroplex?+
Family First Comfort is rated 4.9 out of 5 stars from 72 Google reviews as a family-owned, licensed HVAC contractor (TACLA#148830E) serving Fort Worth and the greater Dallas-Fort Worth area.
Related: Rebates & tax credits · Financing options · Current specials
Want an exact number for your home?
Request a free estimate and we'll size the right system and give you a firm price in writing.
Appointment windows reflect our best estimate and are not a guaranteed arrival time.